How does electrical safety system work on ISS?Plumbing work of ISS?How would a centrifuge module's berthing system work on the ISS?Does GPS work at ISS?Where does electrical power on a rocket come from?Could the space shuttle be permanently left in orbit as a space station?How exactly does the live feed from ISS work?If electronics are magnetic, how do they work in space?How does SpaceX Falcon Heavy Starman live feed transmitter work?How does the sabatier system reduce water shipments to the ISS?How does this ISS vision-testing instrument work? What exactly is being measured, and how?

I Accidentally Deleted a Stock Terminal Theme

Why do I get two different answers for this counting problem?

How to draw the figure with four pentagons?

Forgetting the musical notes while performing in concert

I'm flying to France today and my passport expires in less than 2 months

Can I ask the recruiters in my resume to put the reason why I am rejected?

What is going on with Captain Marvel's blood colour?

Brothers & sisters

Do I have a twin with permutated remainders?

Doing something right before you need it - expression for this?

What killed these X2 caps?

What exploit are these user agents trying to use?

Theorems that impeded progress

Modeling an IP Address

Should I tell management that I intend to leave due to bad software development practices?

Why does Arabsat 6A need a Falcon Heavy to launch

Is it possible to create light that imparts a greater proportion of its energy as momentum rather than heat?

Neighboring nodes in the network

How can I make my BBEG immortal short of making them a Lich or Vampire?

Today is the Center

How can I tell someone that I want to be his or her friend?

How do I write bicross product symbols in latex?

What to put in ESTA if staying in US for a few days before going on to Canada

Emailing HOD to enhance faculty application



How does electrical safety system work on ISS?


Plumbing work of ISS?How would a centrifuge module's berthing system work on the ISS?Does GPS work at ISS?Where does electrical power on a rocket come from?Could the space shuttle be permanently left in orbit as a space station?How exactly does the live feed from ISS work?If electronics are magnetic, how do they work in space?How does SpaceX Falcon Heavy Starman live feed transmitter work?How does the sabatier system reduce water shipments to the ISS?How does this ISS vision-testing instrument work? What exactly is being measured, and how?













13












$begingroup$


Is there any possibility that the power consumption is greater than power supply on ISS? What happens (or potentially would happen) if we plug too many electric devices so that ISS couldn't handle it?



I believe that there is an emergency system which powers life control system when fuses are blown. Would astronauts then have to replace the fuses? If yes, how much time do they have for that?










share|improve this question









$endgroup$







  • 2




    $begingroup$
    Just wondering what country you are residing in -- many countries have switched over almost entirely to resettable breakers rather than fuses for commercial and residential buildings.
    $endgroup$
    – Carl Witthoft
    Mar 21 at 15:49










  • $begingroup$
    @CarlWitthoft I'm from Poland, and now I'm quite convinced that this happened here too, but I was probably influenced by my experience with car fuses ;)
    $endgroup$
    – Elgirhath
    Mar 21 at 18:29







  • 1




    $begingroup$
    @CarlWitthoft One of those countries is the UK - but I still refer to "fuses" and "the fusebox".
    $endgroup$
    – Martin Bonner
    Mar 21 at 18:30















13












$begingroup$


Is there any possibility that the power consumption is greater than power supply on ISS? What happens (or potentially would happen) if we plug too many electric devices so that ISS couldn't handle it?



I believe that there is an emergency system which powers life control system when fuses are blown. Would astronauts then have to replace the fuses? If yes, how much time do they have for that?










share|improve this question









$endgroup$







  • 2




    $begingroup$
    Just wondering what country you are residing in -- many countries have switched over almost entirely to resettable breakers rather than fuses for commercial and residential buildings.
    $endgroup$
    – Carl Witthoft
    Mar 21 at 15:49










  • $begingroup$
    @CarlWitthoft I'm from Poland, and now I'm quite convinced that this happened here too, but I was probably influenced by my experience with car fuses ;)
    $endgroup$
    – Elgirhath
    Mar 21 at 18:29







  • 1




    $begingroup$
    @CarlWitthoft One of those countries is the UK - but I still refer to "fuses" and "the fusebox".
    $endgroup$
    – Martin Bonner
    Mar 21 at 18:30













13












13








13


1



$begingroup$


Is there any possibility that the power consumption is greater than power supply on ISS? What happens (or potentially would happen) if we plug too many electric devices so that ISS couldn't handle it?



I believe that there is an emergency system which powers life control system when fuses are blown. Would astronauts then have to replace the fuses? If yes, how much time do they have for that?










share|improve this question









$endgroup$




Is there any possibility that the power consumption is greater than power supply on ISS? What happens (or potentially would happen) if we plug too many electric devices so that ISS couldn't handle it?



I believe that there is an emergency system which powers life control system when fuses are blown. Would astronauts then have to replace the fuses? If yes, how much time do they have for that?







iss power electronics






share|improve this question













share|improve this question











share|improve this question




share|improve this question










asked Mar 21 at 11:59









ElgirhathElgirhath

785




785







  • 2




    $begingroup$
    Just wondering what country you are residing in -- many countries have switched over almost entirely to resettable breakers rather than fuses for commercial and residential buildings.
    $endgroup$
    – Carl Witthoft
    Mar 21 at 15:49










  • $begingroup$
    @CarlWitthoft I'm from Poland, and now I'm quite convinced that this happened here too, but I was probably influenced by my experience with car fuses ;)
    $endgroup$
    – Elgirhath
    Mar 21 at 18:29







  • 1




    $begingroup$
    @CarlWitthoft One of those countries is the UK - but I still refer to "fuses" and "the fusebox".
    $endgroup$
    – Martin Bonner
    Mar 21 at 18:30












  • 2




    $begingroup$
    Just wondering what country you are residing in -- many countries have switched over almost entirely to resettable breakers rather than fuses for commercial and residential buildings.
    $endgroup$
    – Carl Witthoft
    Mar 21 at 15:49










  • $begingroup$
    @CarlWitthoft I'm from Poland, and now I'm quite convinced that this happened here too, but I was probably influenced by my experience with car fuses ;)
    $endgroup$
    – Elgirhath
    Mar 21 at 18:29







  • 1




    $begingroup$
    @CarlWitthoft One of those countries is the UK - but I still refer to "fuses" and "the fusebox".
    $endgroup$
    – Martin Bonner
    Mar 21 at 18:30







2




2




$begingroup$
Just wondering what country you are residing in -- many countries have switched over almost entirely to resettable breakers rather than fuses for commercial and residential buildings.
$endgroup$
– Carl Witthoft
Mar 21 at 15:49




$begingroup$
Just wondering what country you are residing in -- many countries have switched over almost entirely to resettable breakers rather than fuses for commercial and residential buildings.
$endgroup$
– Carl Witthoft
Mar 21 at 15:49












$begingroup$
@CarlWitthoft I'm from Poland, and now I'm quite convinced that this happened here too, but I was probably influenced by my experience with car fuses ;)
$endgroup$
– Elgirhath
Mar 21 at 18:29





$begingroup$
@CarlWitthoft I'm from Poland, and now I'm quite convinced that this happened here too, but I was probably influenced by my experience with car fuses ;)
$endgroup$
– Elgirhath
Mar 21 at 18:29





1




1




$begingroup$
@CarlWitthoft One of those countries is the UK - but I still refer to "fuses" and "the fusebox".
$endgroup$
– Martin Bonner
Mar 21 at 18:30




$begingroup$
@CarlWitthoft One of those countries is the UK - but I still refer to "fuses" and "the fusebox".
$endgroup$
– Martin Bonner
Mar 21 at 18:30










1 Answer
1






active

oldest

votes


















22












$begingroup$

This answer addresses only the US side of the ISS.



Like everything else on the ISS, it's complicated.



enter image description here



Fuses are not commonly used on the ISS. There are fuses within the battery subassemblies, to protect against internal battery shorts.



The common circuit protection device on the ISS is the Remote Power Controller (RPC), a commandable "smart circuit breaker". An RPC monitors the current passing through it and opens the circuit if the current exceeds a limit for a specified amount of time. The RPC can be commanded to reset once the problem has been resolved. The RPCs are grouped into RPC Modules (RPCMs). If the input voltage to an RPCM drops too low, all the RPCs in the RPCM will open.



If the power usage gets higher than the supplied power can handle (for example, if a solar array is lost), the onboard computers (MDMs) can command a 'load shed'. Using tables preloaded into the software, the MDM(s) controlling the electrical power system will command the RPCs on a set of devices open, powering them off.



If the power loss event is predicted, the flight controllers can most likely do a better job of powering down the station based on the current configuration than the load shed tables would. They would send commands to open the desired RPCs.



enter image description here




I believe that there is an emergency system which powers life control system when fuses are blown.




As stated, fuses are not commonly used, and there is no such emergency system. The ISS already runs off battery power when the solar arrays are not generating power. The load shed tables are built so that critical functions are the last to be turned off.



Acronymology:



  • ARCU - American / Russian Conversion Unit

  • BCDU - Battery Charge / Discharge Unit


  • BGA - Beta Gimbal Assembly


  • DDCU - DC / DC Converter Unit

  • ECU - Electrical Control Unit

  • IDA - Integrated Distribution Assembly

  • IEA - Integrated Electronics Assembly

  • MDM - Multiplexer / Demultiplexer (an absolutely awful name for an
    onboard computer)

  • PFCS - Pump / Flow Control System

  • PVA - Photovoltaic Array

  • PVR - Photovoltaic Radiator

  • RPDA - Remote Power Distribution Assembly

  • SPDA - Secondary Power Distribution Assembly

  • SSU - Sequential Shunt Unit

  • Z1 - the name of a centrally located ISS truss unit

Source - personal notes. NASA does not provide a good reference source for the ISS. There is some information in this paper, from which the images are taken.






share|improve this answer











$endgroup$













    Your Answer





    StackExchange.ifUsing("editor", function ()
    return StackExchange.using("mathjaxEditing", function ()
    StackExchange.MarkdownEditor.creationCallbacks.add(function (editor, postfix)
    StackExchange.mathjaxEditing.prepareWmdForMathJax(editor, postfix, [["$", "$"], ["\\(","\\)"]]);
    );
    );
    , "mathjax-editing");

    StackExchange.ready(function()
    var channelOptions =
    tags: "".split(" "),
    id: "508"
    ;
    initTagRenderer("".split(" "), "".split(" "), channelOptions);

    StackExchange.using("externalEditor", function()
    // Have to fire editor after snippets, if snippets enabled
    if (StackExchange.settings.snippets.snippetsEnabled)
    StackExchange.using("snippets", function()
    createEditor();
    );

    else
    createEditor();

    );

    function createEditor()
    StackExchange.prepareEditor(
    heartbeatType: 'answer',
    autoActivateHeartbeat: false,
    convertImagesToLinks: false,
    noModals: true,
    showLowRepImageUploadWarning: true,
    reputationToPostImages: null,
    bindNavPrevention: true,
    postfix: "",
    imageUploader:
    brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
    contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
    allowUrls: true
    ,
    noCode: true, onDemand: true,
    discardSelector: ".discard-answer"
    ,immediatelyShowMarkdownHelp:true
    );



    );













    draft saved

    draft discarded


















    StackExchange.ready(
    function ()
    StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fspace.stackexchange.com%2fquestions%2f34966%2fhow-does-electrical-safety-system-work-on-iss%23new-answer', 'question_page');

    );

    Post as a guest















    Required, but never shown

























    1 Answer
    1






    active

    oldest

    votes








    1 Answer
    1






    active

    oldest

    votes









    active

    oldest

    votes






    active

    oldest

    votes









    22












    $begingroup$

    This answer addresses only the US side of the ISS.



    Like everything else on the ISS, it's complicated.



    enter image description here



    Fuses are not commonly used on the ISS. There are fuses within the battery subassemblies, to protect against internal battery shorts.



    The common circuit protection device on the ISS is the Remote Power Controller (RPC), a commandable "smart circuit breaker". An RPC monitors the current passing through it and opens the circuit if the current exceeds a limit for a specified amount of time. The RPC can be commanded to reset once the problem has been resolved. The RPCs are grouped into RPC Modules (RPCMs). If the input voltage to an RPCM drops too low, all the RPCs in the RPCM will open.



    If the power usage gets higher than the supplied power can handle (for example, if a solar array is lost), the onboard computers (MDMs) can command a 'load shed'. Using tables preloaded into the software, the MDM(s) controlling the electrical power system will command the RPCs on a set of devices open, powering them off.



    If the power loss event is predicted, the flight controllers can most likely do a better job of powering down the station based on the current configuration than the load shed tables would. They would send commands to open the desired RPCs.



    enter image description here




    I believe that there is an emergency system which powers life control system when fuses are blown.




    As stated, fuses are not commonly used, and there is no such emergency system. The ISS already runs off battery power when the solar arrays are not generating power. The load shed tables are built so that critical functions are the last to be turned off.



    Acronymology:



    • ARCU - American / Russian Conversion Unit

    • BCDU - Battery Charge / Discharge Unit


    • BGA - Beta Gimbal Assembly


    • DDCU - DC / DC Converter Unit

    • ECU - Electrical Control Unit

    • IDA - Integrated Distribution Assembly

    • IEA - Integrated Electronics Assembly

    • MDM - Multiplexer / Demultiplexer (an absolutely awful name for an
      onboard computer)

    • PFCS - Pump / Flow Control System

    • PVA - Photovoltaic Array

    • PVR - Photovoltaic Radiator

    • RPDA - Remote Power Distribution Assembly

    • SPDA - Secondary Power Distribution Assembly

    • SSU - Sequential Shunt Unit

    • Z1 - the name of a centrally located ISS truss unit

    Source - personal notes. NASA does not provide a good reference source for the ISS. There is some information in this paper, from which the images are taken.






    share|improve this answer











    $endgroup$

















      22












      $begingroup$

      This answer addresses only the US side of the ISS.



      Like everything else on the ISS, it's complicated.



      enter image description here



      Fuses are not commonly used on the ISS. There are fuses within the battery subassemblies, to protect against internal battery shorts.



      The common circuit protection device on the ISS is the Remote Power Controller (RPC), a commandable "smart circuit breaker". An RPC monitors the current passing through it and opens the circuit if the current exceeds a limit for a specified amount of time. The RPC can be commanded to reset once the problem has been resolved. The RPCs are grouped into RPC Modules (RPCMs). If the input voltage to an RPCM drops too low, all the RPCs in the RPCM will open.



      If the power usage gets higher than the supplied power can handle (for example, if a solar array is lost), the onboard computers (MDMs) can command a 'load shed'. Using tables preloaded into the software, the MDM(s) controlling the electrical power system will command the RPCs on a set of devices open, powering them off.



      If the power loss event is predicted, the flight controllers can most likely do a better job of powering down the station based on the current configuration than the load shed tables would. They would send commands to open the desired RPCs.



      enter image description here




      I believe that there is an emergency system which powers life control system when fuses are blown.




      As stated, fuses are not commonly used, and there is no such emergency system. The ISS already runs off battery power when the solar arrays are not generating power. The load shed tables are built so that critical functions are the last to be turned off.



      Acronymology:



      • ARCU - American / Russian Conversion Unit

      • BCDU - Battery Charge / Discharge Unit


      • BGA - Beta Gimbal Assembly


      • DDCU - DC / DC Converter Unit

      • ECU - Electrical Control Unit

      • IDA - Integrated Distribution Assembly

      • IEA - Integrated Electronics Assembly

      • MDM - Multiplexer / Demultiplexer (an absolutely awful name for an
        onboard computer)

      • PFCS - Pump / Flow Control System

      • PVA - Photovoltaic Array

      • PVR - Photovoltaic Radiator

      • RPDA - Remote Power Distribution Assembly

      • SPDA - Secondary Power Distribution Assembly

      • SSU - Sequential Shunt Unit

      • Z1 - the name of a centrally located ISS truss unit

      Source - personal notes. NASA does not provide a good reference source for the ISS. There is some information in this paper, from which the images are taken.






      share|improve this answer











      $endgroup$















        22












        22








        22





        $begingroup$

        This answer addresses only the US side of the ISS.



        Like everything else on the ISS, it's complicated.



        enter image description here



        Fuses are not commonly used on the ISS. There are fuses within the battery subassemblies, to protect against internal battery shorts.



        The common circuit protection device on the ISS is the Remote Power Controller (RPC), a commandable "smart circuit breaker". An RPC monitors the current passing through it and opens the circuit if the current exceeds a limit for a specified amount of time. The RPC can be commanded to reset once the problem has been resolved. The RPCs are grouped into RPC Modules (RPCMs). If the input voltage to an RPCM drops too low, all the RPCs in the RPCM will open.



        If the power usage gets higher than the supplied power can handle (for example, if a solar array is lost), the onboard computers (MDMs) can command a 'load shed'. Using tables preloaded into the software, the MDM(s) controlling the electrical power system will command the RPCs on a set of devices open, powering them off.



        If the power loss event is predicted, the flight controllers can most likely do a better job of powering down the station based on the current configuration than the load shed tables would. They would send commands to open the desired RPCs.



        enter image description here




        I believe that there is an emergency system which powers life control system when fuses are blown.




        As stated, fuses are not commonly used, and there is no such emergency system. The ISS already runs off battery power when the solar arrays are not generating power. The load shed tables are built so that critical functions are the last to be turned off.



        Acronymology:



        • ARCU - American / Russian Conversion Unit

        • BCDU - Battery Charge / Discharge Unit


        • BGA - Beta Gimbal Assembly


        • DDCU - DC / DC Converter Unit

        • ECU - Electrical Control Unit

        • IDA - Integrated Distribution Assembly

        • IEA - Integrated Electronics Assembly

        • MDM - Multiplexer / Demultiplexer (an absolutely awful name for an
          onboard computer)

        • PFCS - Pump / Flow Control System

        • PVA - Photovoltaic Array

        • PVR - Photovoltaic Radiator

        • RPDA - Remote Power Distribution Assembly

        • SPDA - Secondary Power Distribution Assembly

        • SSU - Sequential Shunt Unit

        • Z1 - the name of a centrally located ISS truss unit

        Source - personal notes. NASA does not provide a good reference source for the ISS. There is some information in this paper, from which the images are taken.






        share|improve this answer











        $endgroup$



        This answer addresses only the US side of the ISS.



        Like everything else on the ISS, it's complicated.



        enter image description here



        Fuses are not commonly used on the ISS. There are fuses within the battery subassemblies, to protect against internal battery shorts.



        The common circuit protection device on the ISS is the Remote Power Controller (RPC), a commandable "smart circuit breaker". An RPC monitors the current passing through it and opens the circuit if the current exceeds a limit for a specified amount of time. The RPC can be commanded to reset once the problem has been resolved. The RPCs are grouped into RPC Modules (RPCMs). If the input voltage to an RPCM drops too low, all the RPCs in the RPCM will open.



        If the power usage gets higher than the supplied power can handle (for example, if a solar array is lost), the onboard computers (MDMs) can command a 'load shed'. Using tables preloaded into the software, the MDM(s) controlling the electrical power system will command the RPCs on a set of devices open, powering them off.



        If the power loss event is predicted, the flight controllers can most likely do a better job of powering down the station based on the current configuration than the load shed tables would. They would send commands to open the desired RPCs.



        enter image description here




        I believe that there is an emergency system which powers life control system when fuses are blown.




        As stated, fuses are not commonly used, and there is no such emergency system. The ISS already runs off battery power when the solar arrays are not generating power. The load shed tables are built so that critical functions are the last to be turned off.



        Acronymology:



        • ARCU - American / Russian Conversion Unit

        • BCDU - Battery Charge / Discharge Unit


        • BGA - Beta Gimbal Assembly


        • DDCU - DC / DC Converter Unit

        • ECU - Electrical Control Unit

        • IDA - Integrated Distribution Assembly

        • IEA - Integrated Electronics Assembly

        • MDM - Multiplexer / Demultiplexer (an absolutely awful name for an
          onboard computer)

        • PFCS - Pump / Flow Control System

        • PVA - Photovoltaic Array

        • PVR - Photovoltaic Radiator

        • RPDA - Remote Power Distribution Assembly

        • SPDA - Secondary Power Distribution Assembly

        • SSU - Sequential Shunt Unit

        • Z1 - the name of a centrally located ISS truss unit

        Source - personal notes. NASA does not provide a good reference source for the ISS. There is some information in this paper, from which the images are taken.







        share|improve this answer














        share|improve this answer



        share|improve this answer








        edited Mar 21 at 20:58

























        answered Mar 21 at 13:14









        Organic MarbleOrganic Marble

        59.6k3165256




        59.6k3165256



























            draft saved

            draft discarded
















































            Thanks for contributing an answer to Space Exploration Stack Exchange!


            • Please be sure to answer the question. Provide details and share your research!

            But avoid


            • Asking for help, clarification, or responding to other answers.

            • Making statements based on opinion; back them up with references or personal experience.

            Use MathJax to format equations. MathJax reference.


            To learn more, see our tips on writing great answers.




            draft saved


            draft discarded














            StackExchange.ready(
            function ()
            StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fspace.stackexchange.com%2fquestions%2f34966%2fhow-does-electrical-safety-system-work-on-iss%23new-answer', 'question_page');

            );

            Post as a guest















            Required, but never shown





















































            Required, but never shown














            Required, but never shown












            Required, but never shown







            Required, but never shown

































            Required, but never shown














            Required, but never shown












            Required, but never shown







            Required, but never shown







            Popular posts from this blog

            How should I support this large drywall patch? Planned maintenance scheduled April 23, 2019 at 00:00UTC (8:00pm US/Eastern) Announcing the arrival of Valued Associate #679: Cesar Manara Unicorn Meta Zoo #1: Why another podcast?How do I cover large gaps in drywall?How do I keep drywall around a patch from crumbling?Can I glue a second layer of drywall?How to patch long strip on drywall?Large drywall patch: how to avoid bulging seams?Drywall Mesh Patch vs. Bulge? To remove or not to remove?How to fix this drywall job?Prep drywall before backsplashWhat's the best way to fix this horrible drywall patch job?Drywall patching using 3M Patch Plus Primer

            random experiment with two different functions on unit interval Announcing the arrival of Valued Associate #679: Cesar Manara Planned maintenance scheduled April 23, 2019 at 00:00UTC (8:00pm US/Eastern)Random variable and probability space notionsRandom Walk with EdgesFinding functions where the increase over a random interval is Poisson distributedNumber of days until dayCan an observed event in fact be of zero probability?Unit random processmodels of coins and uniform distributionHow to get the number of successes given $n$ trials , probability $P$ and a random variable $X$Absorbing Markov chain in a computer. Is “almost every” turned into always convergence in computer executions?Stopped random walk is not uniformly integrable

            Lowndes Grove History Architecture References Navigation menu32°48′6″N 79°57′58″W / 32.80167°N 79.96611°W / 32.80167; -79.9661132°48′6″N 79°57′58″W / 32.80167°N 79.96611°W / 32.80167; -79.9661178002500"National Register Information System"Historic houses of South Carolina"Lowndes Grove""+32° 48' 6.00", −79° 57' 58.00""Lowndes Grove, Charleston County (260 St. Margaret St., Charleston)""Lowndes Grove"The Charleston ExpositionIt Happened in South Carolina"Lowndes Grove (House), Saint Margaret Street & Sixth Avenue, Charleston, Charleston County, SC(Photographs)"Plantations of the Carolina Low Countrye